My project n26 build with Dyno!!

Kel918 · 07-27-2020, 07:43 PM

I bought a base 328i x-drive last year for my daily driver, but I had to do some upgrades. At first I started with least expensive upgrades as this was just my daily driver then worked my way up. I dynoed the car today @ prime motoring in Wallington NJ. On a Mustang Awd Dyno it put down 262whp and 294wtq. A mustang dyno reads between 11-14% lower than a dynojet. If I did an 11% calculation it would be 290whp and 326wtq. Only mods Jb+, ebay G-plus intercooler, test pipe and 340i exhaust.

POWER UPGRADES:

1.) BMS- Jb+ (used) $85
2.) Intercooler- G-plus (ebay) $221

SUSPENSION UPGRADES:

1.) Front sway bar- H&R x-drive
2.) Rear sway bar- m3/m4 competition
3.) Front and Rear struts/shocks- Bilstein B8
4.) Springs- Godspeed traction s (ebay) $135
5.) Bumpstops- Dinan
6.) Front strut bar- OBX Racing front strut $156 (Amazon)

Brake UPGRADES:

1.) Front Calipers- F10 M5- 6 Piston calipers
2.) Rear Calipers- F80/82- 2 Piston caliper
3.) Front rotor- F10 M5 - 400mm
4.) Rear rotor- F30 M sport- 345mm (ebay) $68.20

EXHAUST UPGRADES:

1.) Test pipe- Circuit Werks (ebay) $159.99
2.) Exhaust- F30- 340i dual exhaust (used $240)

EXTERIOR UPGRADES:

1.) Front bumper- M sport (buy complete with all grills, etc..)
2.) Rear bumper- M sport $188.02
3.) Rear diffuser- M sport quad diffuser $98.99
4.) Sideskirts- M sport $120.98
5.) Sideskirt extensions -HC1 (ebay) $83
6.) Front lip- Mp style (ebay) $126
7.) Rear lip- V style (ebay) $108.65

Kel918 · 07-27-2020, 07:49 PM

Trying to post the dyno graphs

VipinLJ · 07-27-2020, 10:07 PM

Not bad at all for a JB+. I'm assuming you didn't do a run with the JB+ uninstalled?

Kel918 · 07-28-2020, 06:50 AM

It slipped my mind to run it without the Jb+, I was in a rush since I had to go to work right after

mike@x-ph.com · 07-28-2020, 09:47 AM

Kel918 · 07-28-2020, 09:00 PM

quick question, does anyone know what's the biggest size air intake pipe you can use without throwing off the maf sensor ?

Fr3sh · 07-29-2020, 02:30 AM

Nice! Get bm3

Kel918 · 07-29-2020, 10:49 AM

That'll be a future mod, I really need to know the highest diameter piping that the maf sensor could read without any problems. Could it read 3.5-4.0 inch piping

07-27-2020, 07:43 PM	#1
Kel918 Private First Class 54 Rep 185 Posts Drives: 2013 bmw 328ix Join Date: Jan 2019 Location: New jersey iTrader: (1)	My project n26 build with Dyno!! I bought a base 328i x-drive last year for my daily driver, but I had to do some upgrades. At first I started with least expensive upgrades as this was just my daily driver then worked my way up. I dynoed the car today @ prime motoring in Wallington NJ. On a Mustang Awd Dyno it put down 262whp and 294wtq. A mustang dyno reads between 11-14% lower than a dynojet. If I did an 11% calculation it would be 290whp and 326wtq. Only mods Jb+, ebay G-plus intercooler, test pipe and 340i exhaust. POWER UPGRADES: 1.) BMS- Jb+ (used) $85 2.) Intercooler- G-plus (ebay) $221 SUSPENSION UPGRADES: 1.) Front sway bar- H&R x-drive 2.) Rear sway bar- m3/m4 competition 3.) Front and Rear struts/shocks- Bilstein B8 4.) Springs- Godspeed traction s (ebay) $135 5.) Bumpstops- Dinan 6.) Front strut bar- OBX Racing front strut $156 (Amazon) Brake UPGRADES: 1.) Front Calipers- F10 M5- 6 Piston calipers 2.) Rear Calipers- F80/82- 2 Piston caliper 3.) Front rotor- F10 M5 - 400mm 4.) Rear rotor- F30 M sport- 345mm (ebay) $68.20 EXHAUST UPGRADES: 1.) Test pipe- Circuit Werks (ebay) $159.99 2.) Exhaust- F30- 340i dual exhaust (used $240) EXTERIOR UPGRADES: 1.) Front bumper- M sport (buy complete with all grills, etc..) 2.) Rear bumper- M sport $188.02 3.) Rear diffuser- M sport quad diffuser $98.99 4.) Sideskirts- M sport $120.98 5.) Sideskirt extensions -HC1 (ebay) $83 6.) Front lip- Mp style (ebay) $126 7.) Rear lip- V style (ebay) $108.65 Attached Images Last edited by Kel918; 09-05-2020 at 01:11 PM..
	Appreciate 0 Tweet Quote

07-27-2020, 10:07 PM	#3
VipinLJ Petrolhead 1943 Rep 3,521 Posts Drives: ‘20 330i,‘16 X3,‘18 SQ5,‘17 A7 Join Date: Nov 2019 Location: Illinois iTrader: (2)	Not bad at all for a JB+. I'm assuming you didn't do a run with the JB+ uninstalled? __________________ Current: 2020 BMW 330i xDrive 2018 Audi SQ5 Prestige 2017 Audi A7 Prestige
	Appreciate 0 Quote

07-28-2020, 06:50 AM	#4
Kel918 Private First Class 54 Rep 185 Posts Drives: 2013 bmw 328ix Join Date: Jan 2019 Location: New jersey iTrader: (1)	It slipped my mind to run it without the Jb+, I was in a rush since I had to go to work right after
	Appreciate 1 VipinLJ1943.00 Quote

07-28-2020, 09:47 AM	#5
mike@x-ph.com BimmerPost Supporting Vendor 24201 Rep 190,807 Posts Drives: 07-335/12-328/18-M4/21-M4CP Join Date: Sep 2013 Location: Las Vegas iTrader: (23)	__________________ Check out our current sale by clicking on this link! https://x-ph.com/sale/ Phone number 702-494-9435
	Appreciate 0 Quote

07-28-2020, 09:00 PM	#6
Kel918 Private First Class 54 Rep 185 Posts Drives: 2013 bmw 328ix Join Date: Jan 2019 Location: New jersey iTrader: (1)	quick question, does anyone know what's the biggest size air intake pipe you can use without throwing off the maf sensor ?
	Appreciate 0 Quote

07-29-2020, 02:30 AM	#7
Fr3sh #im_2_Fr3sh 30 Rep 247 Posts Drives: Bmw 428i xdrive Join Date: Jan 2018 Location: Ny iTrader: (0)	Nice! Get bm3 __________________ 2014 428i xDrive F32 \| Injen Cai \| Er Intercooler \| Er Chargepipe \| Er Tic Pipe \| Er Catless Downpipe \| Bm3 - Cary Jordan tuned 93 oct \| Gfb Dv \| Ngk L/I Spark Plugs \| Cf High Kick Trunk Spoiler v1 \| Black Grilles \| 35% Suntek Tints \| Michelin pss4 \| Awe Quad Exhaust w/ Resonated Midpipe \| Interior Mods \| Mst Turbo Inlet \| Pure Stage 2 Turbo \| Arp rod bolts \| Fuel-it Stage 2 Lpfp \| Braum Elite x seats \| Mishimoto Oil-catch can \|
	Appreciate 0 Quote

07-29-2020, 10:49 AM	#8
Kel918 Private First Class 54 Rep 185 Posts Drives: 2013 bmw 328ix Join Date: Jan 2019 Location: New jersey iTrader: (1)	That'll be a future mod, I really need to know the highest diameter piping that the maf sensor could read without any problems. Could it read 3.5-4.0 inch piping Last edited by Kel918; 08-03-2020 at 06:27 PM..
	Appreciate 0 Quote