07-10-2014, 11:21 AM | #4 |
Colonel
383
Rep 2,988
Posts |
|
Appreciate
0
|
07-14-2014, 08:23 AM | #5 |
Captain
26
Rep 688
Posts |
Bought my M3 12/22/12 and it still looks brand new. I orderd the Xpel full hood, front sides, front bumper, mirrors and rear wheel arches for my '13 M3 at he BMW dealer. Best money ever spend. Easy to seal, wash and wax using the Xpel products.
http://www.xpel.com/ |
Appreciate
0
|
07-14-2014, 09:41 AM | #6 | |
Colonel
383
Rep 2,988
Posts |
Quote:
|
|
Appreciate
0
|
07-26-2014, 10:08 PM | #8 | |
Brigadier General
1002
Rep 3,052
Posts |
Quote:
__________________
2022 RAM TRX
2021 Ford Bronco 2022 BMW M3 |
|
Appreciate
0
|
07-26-2014, 10:10 PM | #9 |
Major
747
Rep 1,478
Posts |
Very interested to see also as I plan on doing the very same
__________________
Individual M4 Convertible ED Sept 2014
|
Appreciate
0
|
07-27-2014, 12:18 AM | #11 |
X3M Comp
441
Rep 717
Posts |
|
Appreciate
0
|
07-27-2014, 03:43 PM | #12 |
Major
747
Rep 1,478
Posts |
Wow - looks very sharp - can't really see close enough to tell how well the seams/edges look but either way looks very nice indeed. Will be doing the same (with the amount construction and crap on Houston roads front ends and bonnets get hammered here).
__________________
Individual M4 Convertible ED Sept 2014
|
Appreciate
0
|
07-29-2014, 10:16 AM | #13 |
Colonel
383
Rep 2,988
Posts |
Good news all around. Can somebody post close up pics of the lower intake areas? I'd like to see how close the precut kit comes to the various folds and corners down low.
|
Appreciate
0
|
07-29-2014, 10:19 AM | #14 |
BMW Fanatic
374
Rep 1,413
Posts
Drives: 2020 X3 M
Join Date: Jun 2014
Location: Austin, TX
|
I'm getting mine done tomorrow I will post some pics when it is done.
__________________
SteveSpy
Current Ride: 2020 X3 M |
Appreciate
0
|
07-29-2014, 01:38 PM | #15 |
Major General
286
Rep 5,686
Posts |
I am test fitting a car shortly. I am actually removing the headlights // kidney grill for super flush design. Updates to come soon.
__________________
*************************************
Un4gettable 435i Extended Test drive thread: http://www.f30post.com/forums/showthread.php?t=881491 |
Appreciate
0
|
07-30-2014, 02:45 PM | #16 |
Enlisted Member
12
Rep 47
Posts |
Hey everyone - I apologize if this is a really, really dumb question - but once you have an XPEL clear bra system professionally installed - why would you ever have to wax your car? Since you're essentially cleaning a plastic film at that point don't you just have to use a pressure washer and soap? Apologize for being a newbie. It seems that XPEL is a great investment because it simplifies exterior car care...
|
Appreciate
0
|
07-30-2014, 03:06 PM | #17 |
Captain
219
Rep 949
Posts |
I have it installed on my car and the coverage is pretty damn good. Plus i have the whole hood, fenders, mirrors and parts of the side skirt. If you are at bimmerfest, stop by ACM's booth to check it out.
|
Appreciate
0
|
07-30-2014, 06:00 PM | #18 |
Captain
97
Rep 635
Posts
Drives: 2018 Audi TTRS
Join Date: May 2012
Location: Virginia
|
I have Xpel on my front bumper, front 1/2 of hood, rear bumper near trunk, door handle area and on the side skirts/rocker panels. I have had to have it touched up a couple of times and still have to have one area on the rocker panel touched up because it delaminates/comes off at the edges. I didn't have this problem with my E92 M3 but for some reason it is not sticking as well on my M4.. Has anyone else run into this problem?
|
Appreciate
0
|
09-18-2014, 12:51 PM | #21 |
Private
32
Rep 87
Posts |
I will take some photos of mine that was done yesterday. On the whole, I am not very pleased with the patterns and the way the corners came out. I wish I had seen others photos before taking the plunge. I will likely go back to have them fix some of the edges and corners but I do not think there is a lot that can be done.
|
Appreciate
0
|
09-18-2014, 12:53 PM | #22 | |
Colonel
383
Rep 2,988
Posts |
Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|